USB-ML-Universal
USB Multilink Universal Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

• Support device：Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices .
• USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Works with target voltage:1.8V-5.25V
• Supports JTAG daisy chaining of multiple ARM MCUs.
• ARM device support includes both the JTAG and SWD protocols.
• Includes USB cable, Type A Male to Type B Male, 6-ft.
• Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices.
• Generates programming voltage on RESET line for RS08 devices.
• Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)
• USB-ML-UNIVERSAL, Rev. E or later requires this RS08 adapter to allow the user to communicate with NXP's RS08 devices.

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

USB-ML-Universal-FX
USB Multilink Universal FX High-Speed Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, MPC5xx/8xx, HC16, 683xx and ARM devices .
• High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- up to 10X faster than the other Multilink models.
• Can be used to power target MCU. Target Voltage: 3.3V, 5.0V
• I/O line clamping for added protection
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Works with target voltage:1.8V-5.25V
• Supports JTAG daisy chaining of multiple ARM MCUs.
• ARM device support includes both the JTAG and SWD protocols
• Includes USB cable, Type A Male to Type B Male, 6-ft.
• Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices.
• Generates programming voltage on RESET line for RS08 devices.
• Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)
• USB-ML-UNIVERSAL-FX Rev. D or later requires this RS08 adapter to allow the user to communicate with NXP's RS08 devices.

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex ,and STM8(with STM8 adapter),Infineon.

• Stand Alone Programming Images (SAP) Support - SAP Images are single file archives which contain all information, data, and algorithms necessary to program target devices with or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• On-Board Storage - Encrypted internal memory, 16MB, 8 images
• Programming Control Port -10-pin port can launch programming, get status/results
• Cloud-Connected Programming Jobs (JOB) Support -Jobs are similar to images but use a connection to the Cloud to provide additional visibility, control, & logging via the free PEcloud service

• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex , and STM8(with STM8 adapter),Infineon ,Renesas（with Renesas adapter）

• Stand Alone Programming Images (SAP) Support - SAP Images are single file archives which contain all information, data, and algorithms necessary to program target devices with or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• Programming Control Port -10-pin port can launch programming, get status/results
• Cloud-Connected Programming Jobs (JOB) Support -Jobs are similar to images but use a connection to the Cloud to provide additional visibility, control, & logging via the free PEcloud service

• High Speed Programming - Download rates reaching 75 Mbits/s
• Larger On-Board Storage - 1+ Gigabyte of encrypted internal memory stores 200+ programming Images/Jobs
• External SDHC Memory - External memory via SDHC Card Port
• Advanced Testing Feature - Run Tests Prior to Programming
• Target Current and Voltage Measurement
• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

• Supports devices:ARM Cortex-M devices only

• Stand Alone Programming Images (SAP) Support - SAP Images are single file archives which contain all information, data, and algorithms necessary to program target devices with or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• On-Board Storage - Encrypted internal memory, 16MB, 8 images
• Programming Control Port -10-pin port can launch programming, get status/results
• Cloud-Connected Programming Jobs (JOB) Support -Jobs are similar to images but use a connection to the Cloud to provide additional visibility, control, & logging via the free PEcloud service

• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

USB-ML-ACP
USB Multilink Debug Probe for ARM® devices (software sold separately)

• Supports devices:ARM Cortex-M devices only
• USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Works with target voltage:1.8V-5.25V
• Supports JTAG daisy chaining of multiple ARM MCUs.
• ARM device support includes both the JTAG and SWD protocols.
• Includes USB cable, Type A Male to Type B Male, 6-ft.

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

PROG-HL-ARM(former PROGACMP)

PROG for ARM® Cortex™ Processors flash programmer software allows you to program/reprogram external flash devices from many ARM device manufacturers in-circuit, via one of PEmicro's compatible hardware debug interfaces. The programmer talks to the processor's Background Debug Mode through a compatible hardware interface (sold separately), which connects the parallel port or USB port of a PC to a mini-10 or mini-20 pin JTAG connector on the target system.

Feature:

• Program
• Verify
• Blank check
• Upload
• Display
• Erase

It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process.
• Restrict Image Use
• Encrypted (eSAP) Programming Images
• Encryption is Easy To Implement and Manage

This allows users to add expandable and easily swappable storage for their programming images. Adding one or more SD cards to your programming setup can give you added flexibility, while encryption helps keep your IP safe. An SD card can easily be moved from Cyclone to Cyclone. Our 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE FX programmers. The SDHC port features are not available on Cyclone LC.

NOTE: This is a legacy product. The latest builds of Cyclone LC have an SD Card slot in the case but NO INTERNAL HARDWARE for this card. Cyclone LC users who wish to purchase this SDHC port activation license should be sure that their Cyclone meets these reuqirements:
Cyclone LC Universal: Rev. B, Date code 0620 or earlier
Cyclone LC ARM: Rev. D, Date code 0620 or earlier
The date code is located on the bottom right of the Cyclone's rear label.

Note: This product includes the license only and does not contain an SDHC card. SDHC cards that are certified to work with PEmicro Cyclones are available separately. PEmicro Cyclones support a minimum of 4GB SDHC card.

CPRO_PWRSUPPLY

Cyclone Power Supply Replacement Part

• Input - 100-240V, 50-60Hz, 0.48A
• Output - 5.9V, 3.0A, 17.7W, Center positive
• 58.25 inches (148cm) cable length
• Barrel connector - 5.5mm outer diameter, 2.5mm inner diameter
• 5 interchangeable international adapters

GDB Server Plug-In for Eclipse-based ARM IDEs

PEmicro's GDB Server Plug-In for Eclipse-based ARM IDEs is the piece which links the GDB debugger to PEmicro hardware, allowing debug and programming via USB, Serial, and Ethernet buses.

• Real-Time Expression View
• OS-Aware Feature Supports FreeRTOS
• Multi-Core project debugging
• Parallel debugging of multiple ARM devices
• Preserve memory ranges across an erase
• Trim Kinetis devices during programming
• EEPROM partitioning capability during flash programming
• SWD and JTAG : Both communications protocols are supported
• JTAG daisy chain support
• Attach to a running part during debug session
• Attach to a running part during debug session
• Semihosting : Simple way for target to send debug messages to the PC. To Eclipse or a Telnet client
• Power Control : Many of PEmicro's debug interfaces can provide power to the target
• Compatible PEmicro hardware interfaces include:

• Multilink ACP - development interface for ARM devices
• Multilink Universal - all-in-one development interface and debug probe
• Multilink Universal FX - Advanced high-speed all-in-one development interface and debug probe
• Cyclone - series production programmers with stand-alone capability
• Cyclone FX - series advanced high speed production programmers with stand-alone capability, speed, storage, security, and other enhancements
• OpenSDA / Embedded OSJTAG- low-cost evaluation boards

C/C++ and Delphi library modules which allow the creation of custom PC applications which use P&E hardware interfaces to control ARM® Cortex™-M processors via background debug mode
FEATURES:

• •Works with ARM Cortex-M devices, including the Kinetis L-Series
• Works through P&E's Multilink Universal, Multilink Universal FX, USB-ML-ACP, CYCLONE-LC-UNIV, CYCLONE-FX-UNIV , CYCLONE-LC-ARM. Note that the SDK will only work for devices supporte4d by the specific P&E hardware interface you are using.
• Provides Interface to Background Debug Mode
• Included in the package are C/C++ and PASCAL modules
• Source and executables provided for both C and PASCAL demos
• Compilers supported:
•UNITACMP and UNITACMP_DIST: MicrosoftVisual C++ 5.0 or greater, Delphi 2.0 or greater
• Development platform: Windows 32-bit, Windows 64-bit (XP, Vista, 7,8,10).
• Very useful for building production line testers